background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults by MDCBy Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE (CAUTION)
AMBER MESSAGE (ADVISORY)
CYAN MESSAGE (STATUS)
WHITE MESSAGE Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

03/03/21

Message Overview:

Message Name:

LOW HYDRAULICS LEVEL
(Service Message)

Message Code:

B3-007773

Associated CAS:

None

Reporting LRU: R HYDR RESERVOIR
System Description: 29-12-00
Schematic Diagram: 29-12-00
Wiring Diagram: 29-31-03

Message Description:

The right hydraulics reservoir report low fluid level. Verify fluid level.

Possible Causes:

  • Right Hydraulic Reservoir Servicing
  • Right Hydraulic Reservoir Quantity Indicator (MT82)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin: None

Forum Articles/Infoservice/Newsletter: None

  1. Message# = 1
  2. Comp Id = MT082.
  3. Fault Logged = AIR, TAXI.
  4. Status = DEFERRED MAINT
  5. Message Type = Service Message.
  6. Timer = 3.
  7. Logic = DWDC2-26 OR DWDC1-28.
  8. {Term Definitions}

    1. DWDC2-26 2X 253 10 EXCT XXXX-XXXX XXXX-XXXX XXTX-XXXX 253B: 14; LOW RIGHT HYDRAULICS LEV.
    2. DWDC1-28 1X 253 01 EXCT XXXX-XXXX XXXX-XXXX XXTX-XXXX 253A: 14; LOW RIGHT HYDRAULICS LEV.

Quick Links:

Quantity Check of the Hydraulic Fluid in the Left and Right Hydraulic Systems AMM 12-12-00-610-801
Servicing of the Hydraulic System Reservoirs AMM 12-12-00-611-801
Bleeding of the Left and Right Hydraulic Systems AMM 29-10-00-870-801
Removal of the Visual Quantity Indicator AMM 29-12-25-000-802
Installation of the Visual Quantity Indicator AMM 29-12-25-400-802
Standard Practices - Replace Wiring SPM 20-12-00-02
Standard Practices - Wire Repair SPM 20-12-10-02

Troubleshooting Recommendations:

CAUTION: Do not operate the hydraulic pumps if the unpressurized reservoir level is less than:

  • 18% for the Left Hydraulic System
  • 38% for the Right Hydraulic System
  • 41% for the Auxiliary Hydraulic System

If the instruction is not obeyed, equipment can be damaged.

  1. Perform a quantity check of the hydraulic fluid in the right hydraulic system per AMM. Service the right hydraulic reservoir as required.
  2. Service the right hydraulic reservoir per AMM as required.
  3. Bleed the right hydraulic reservoir per AMM as required.
  4. Gain access to the MDC by pushing the AICE, ECS and FUEL buttons simultaneously on the right Cursor Control Panel.
  5. Select the CURRENT SERVICE MESSAGES.
  6. Validate that the message LOW HYDRAULICS LEVEL is not displayed.
  7. If the message is posted in the MDC, proceed with the quantity indicator troubleshooting procedure.
  8. If the message is still posted in the MDC, validate that the reservoir quantity indicator is functioning properly.
    NOTE: Do not over-service the reservoir.
  9. Add or bleed hydraulic fluid from the right hydraulic reservoir and make sure that the quantity on the reservoir visual indicator and the HYD synoptic page display varies accordingly.
  10. If the quantity indication on the reservoir quantity indicator or on the HYD synoptic page does NOT vary accordingly, replace the hydraulic reservoir quantity indicator per AMM and repeat troubleshooting procedure.

Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.