background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults by MDCBy Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE (CAUTION)
AMBER MESSAGE (ADVISORY)
CYAN MESSAGE (STATUS)
WHITE MESSAGE Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

03/16/21

Message Overview:

Message Name:

R OB WHEEL SPEED XDCR

Message Code:

B3-007834

Associated CAS:

R OUTBD BRAKE FAIL
(Caution)

Reporting LRU: R O/B TEMP SNSR
System Description: 32-43-00
Schematic Diagram: 32-43-00
Wiring Diagram: 32-43-49

Message Description:

MessageRight outboard Wheel Speed Transducer fault detected by the Brake Control Unit.

NOTE: The failure of the Right Outboard Wheel Speed Transducer may cause a cyan 'SPOILER FAULT' advisory CAS message to be shown and the associated MDC B3-007835 code.

Possible Causes:

  • Wheel Speed Transducer (RH OB) (MT92)
  • Brake Control Unit (BCU) (A67)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin: None

Forum Articles/Infoservice/Newsletter: None

Quick Links:

Removal of the Brake Control Unit AMM 32-43-01-000-801
Installation of the Brake Control Unit AMM 32-43-01-400-801
Removal of the Wheel Speed Transducer AMM 32-43-49-000-801
Installation of the Wheel Speed Transducer AMM 32-43-49-400-801
Operational Test of the Wheel Speed Transducer AMM 32-43-49-710-801
Data Download from the Maintenance Diagnostic Computer (MDC) AMM 45-45-01-970-802
Standard Practices - Replace Wiring SPM 20-12-00-02
Standard Practices - Electrical Wiring-Continuity Test - Adjustment/Test SPM 20-12-01-05
Standard Practices - Wire Repair SPM 20-12-10-02
Standard Practices - Connector Integrity After a Disconnect and Re-Connection SPM 20-20-00-02

Troubleshooting Recommendations:

  1. Access the MDC 'LRU TEST' page.
  2. Carry out the outboard BCU 'WHEEL SPEED XDCR TEST'.

    1. If the RIGHT WHEEL SPEED TRANSDUCER RESISTANCE TEST fails, go to next step.
    2. If the test passed, do close out.

  3. Pull LCBP-C15 (OUTBD BRAKES), LCBP-C14 (WOW B), RCBP-C13 (WOW B/EXT).
  4. Disconnect wheel well connector P516 (4).
  5. Do a resistance check between pins 1 and 2 of connector P516. The resistance-to-temperature reading must be within the limits shown on Figure 1001.

    1. If resistance is not within limits, do the following:

      1. Remove right outboard wheel speed transducer.
      2. Do a resistance check between pins A and B of the wheel speed transducer. The resistance-to-temperature reading must be within the limits shown on Figure 1001.

        1. If resistance is not within limits, replace wheel speed transducer.
        2. If resistance is within limits, repair wiring between P516 and wheel speed transducer.

    2. If resistance is within limits, go to next step.

  6. Replace BCU.
  7. Do close out.

350_32-43-00_gear350_32-43-00_resistance

Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.