background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults by MDCBy Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE (CAUTION)
AMBER MESSAGE (ADVISORY)
CYAN MESSAGE (STATUS)
WHITE MESSAGE Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

03/22/21

Message Overview:


Message Name:

NO R-FMC-6 BUS OUTPUT

Message Code:

B3-006777

Associated CAS:

None

Reporting LRU: FMC 2
System Description: 34-61-00
Schematic Diagram: 34-61-00
Wiring Diagram: None



Message Description:

R-FMC-6 data absent at R-PFD and R-MFD.

Possible Causes:

  • L FMS/L PFD Mode Selection
  • R Flight Management Computer (FMC 1) (A4-FMC1)
  • Junction Box 2 (JB2)
  • Right Adaptive Flight-Display Unit (PFD 2) (A26)
  • Right Adaptive Flight-Display Unit (MFD 2) (A28)
  • Integrated-Avionics Processor System (IAPS) Card Cage (ICC) (A4)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin:

  • AW300-34-0189Pro Line 21 Advanced Avionics Nuisance Messages and FMS-6200 Issues (20501 - 20999)

Forum Articles/Infoservice/Newsletter: None

NOTE: This nuisance message is caused by the FMS-6200 software.
Work Around: Switching to the map function for the Right and / or Left PFD should clear this message.

Quick Links:

Removal of the Junction Box JB2 AMM 24-63-05-000-801
Installation of the Junction Box JB2 AMM 24-63-05-400-801
Removal of the Integrated Avionic Processor System (IAPS) Card Cage (ICC) AMM 31-45-01-000-801
Installation of the Integrated Avionic Processor System (IAPS) Card Cage (ICC) AMM 31-45-01-400-801
Removal of the Adaptive Flight Display Unit (AFD) AMM 31-61-01-000-801
Installation of the Adaptive Flight Display Unit (AFD) AMM 31-61-01-400-801
Removal of the Flight Management Computer (FMC) AMM 34-61-01-000-801
Installation of the Flight Management Computer (FMC) AMM 34-61-01-400-801
Standard Practices - Replace Wiring SPM 20-12-00-02
Standard Practices - Repair Wiring SPM 20-12-10-02

Troubleshooting Recommendations:

  1. Select FMS1 and PPOS Format on L PFD.

    1. If system check passes, do close out.
    2. If fault remains, continue with next step.
      NOTE: Aircraft has to be WOFW for the message to be seen, and logged, on the MDC.

  2. Reset R IAPS (CB2-B6) circuit breaker.

    1. If system check passes, do close out.
    2. If fault remains, continue with next step.

  3. Do wiring checks of the ARINC 429 data bus R-FMC-6 between IAPS connector A4P103 pins 22 & 24, through Junction Box 2, and L PFD connector A27P2 pins 14 & 15 and L MFD connector A29P2 pins 14 & 15. Repair/replace as required.

    1. If system check passes, do close out.
    2. If fault remains, continue with next step.
      NOTE: An internal short of any LRUs connected to this data bus might cause this failure.

  4. Swap FMCs.

    1. If system check passes, do close out.
    2. If fault remains, continue with next step.

  5. Swap PFDs.

    1. If system check passes, do close out.
    2. If fault remains, continue with next step.

  6. Swap MFDs.

    1. If system check passes, do close out.
    2. If fault remains, continue with next step.

  7. Replace IAPS Card Cage (ICC).
  8. Do close out.

Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.