Fault Message:

ACPC EHP 2B CONTACTOR-K17 FAILED

Fault Code:

2451341ACP

Associated CAS:

ELEC SYS FAULT
(Advisory)

During the power on sequence, the Secondary Logic Card (SLC) will verify that the Electric Hydraulic Pump (EHP) Contactor is open and the EHP current sensing circuit is functional. During the continuous monitoring, the SLC will verify that the EHP Contactor status against its trip status and commanded state.

• AC Power Center (ACPC) (A54)
• Secondary Logic Card (SLC)
• AC Power Center (ACPC) Contactor (K17)
• Hydraulic Control Panel (AP4)
• Electric Hydraulic Pump (EHP) 2B (B52)
• Associated Wiring

Advisory Wire/Service Bulletin: None

Forum Articles/Infoservice/Newsletter: None

Past experience:

1. Hyd pump failed in flight with switch in auto:

   1. We did the following procedure and no anomalies noted.
   2. We performed a ground run (ground idle and flight idle) and no anomalies noted.
   3. They flushed the hydraulic system and no anomalies noted.
   4. We instrumented the hydraulic system, performed flight test and found abnormal in-rush current from hydraulic pump with N2 around 90%. The issue was related to the back feed from the engine driven hydraulic pump.
   5. They replaced manifold and fixed the issue.

1. Swap SLCs.

   1. If system checks are good, replace the defective SLC and do close out.
   2. If fault remains, continue with next step.

2. Get access to the ACPC contactor K17.
3. Disconnect contactor K17 connector P205.
4. Turn the BATT MSTR SW to ON.
5. Check for 28 VDC as follows:

   From	To	Result
   P205-1	Ground

   1. If there is 28 VDC, go to step 7.
   2. If there is no 28 VDC, continue with next step.

6. Verify voltage from the TB202-3. Repair as required.

   1. If system checks are good, do close out.
   2. If fault remains, continue with next step.

7. Turn the BATT MSTR SW to OFF.
8. Remove SLC 2.
9. Perform a continuity check with the connections that follows:

   From	To	Result
   P205-22	Ground
   P205-3	Ground
   P210-31	Ground
   P210-28	Ground
   P210-25	Ground
   P210-22	Ground

   1. If there is continuity, go to step 24.
   2. If there is no continuity, continue with next step.

10. Make sure the Hydraulic Pump 2B is select to OFF.CAUTION: To prevent damage to the ACPC motherboard connectors, ensure that the wire jumper pin outside diameter (OD)/socket inside diameter (ID) does not exceed 0.025 inch.
11. Perform a continuity check as follows:

    From	To	Result
    P211C-23	Ground

    1. If there is no continuity, go to step 14.
    2. If there is continuity, continue with next step.

12. Disconnect connector A54P7 and perform a continuity check as follows:

    From	To	Result
    P211C-23	Ground

    1. If there is continuity, go to step 24.
    2. If there is no continuity, continue with next step.

13. Perform a wiring check as follows:

    From	To	Result
    A54P7-N	AP4P2-2
    AP4P2-15	Ground
    AP4P2-15	HYD Panel

    1. If wiring checks are not good, repair defective wiring as required and do close out.
    2. If wiring checks are good, continue with next step.

14. Perform continuity check as follows:

    From	To	Result
    P205-2	Ground

    1. If there is continuity, go to step 16.
    2. If there is no continuity, continue with next step.

15. Verify TB202-7. Repair as required.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.

16. Perform continuity check with the connections that follows:

    From	To	Result
    P205-22	P211C-11
    P205-3	P211C-18

    1. If there is no continuity, go to step 24.
    2. If there is continuity, continue with next step.

17. Select the switch HYD 2B to ON.
18. Perform continuity check as follows:

    From	To	Result
    P211C-23	Ground

    1. If there is continuity, go to step 21.
    2. If there is no continuity, continue with next step.

19. Disconnect connector A54P7 and perform continuity check as follows:

    From	To	Result
    P211C-23	A54J7-N

    1. If there is no continuity, go to step 24.
    2. If there is continuity, continue with next step.

20. Perform continuity check as follows:

    From	To	Result
    A54P7-N	AP4P2-2
    AP4P2-15	Ground
    AP4P2-15	HYD Panel

    1. If there is no continuity, repair defective wiring as required and do close out.
    2. If there is continuity, continue with next step.

21. Perform and record a resistance check with the connections that follows:

    From	To	Result
    P210-22	P210-31
    P210-22	P210-28
    P210-22	P210-25

    1. If the resistance values are not identical, go to step 24.
    2. If the resistance values are identical, continue with next step.

22. Disconnect connector B52P1. Apply AC power and select HYD Pump 2B to ON.

    1. If fault is not present, go to step 25.
    2. If fault is present, continue with next step.

23. Replace contactor K17.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.

24. Replace ACPC.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.

25. Troubleshoot the hydraulic 2B system.
26. Do close out.