background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults By CAIMS By Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE (CAUTION)
AMBER MESSAGE (ADVISORY)
CYAN MESSAGE (STATUS)
WHITE MESSAGE Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

06/25/19

Message Overview:

Fault Message:

SHAKER #1/WRG/SPC CH A

Fault Code:

2730206STL

Associated CAS:

SHAKER 1 FAIL
(Advisory)

Reporting LRU: Stall Protection Computer (SPC)
System Description: 27-32-00
Schematic Diagram: 27-32-00 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wiring Diagram: 27-32-02 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Fault Description:

Channel A of the Stall Protection Computer (SPC) senses a Shaker 1 low current or an over current condition. The error can be found during continuous Built-In Test (BIT) or a Pilot Activated Test (PAT).

Possible Causes:

  • Stick Shaker 1 (A203)
  • Stall Protection Computer (SPC) (A40)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin: None

Forum Articles/Infoservice/Newsletter: None

Quick Links:

Removal of the Stall Protection Computer AMM 27-32-01-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Stall Protection Computer AMM 27-32-01-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Stick Shakers AMM 27-32-05-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Stick Shakers AMM 27-32-05-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wire Repair - Maintenance Practices - ALL SPM 20-12-10-02 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Troubleshooting Recommendations:

  1. Make sure the connector (A203) and the wires connect on the stick shaker 1 are not damaged.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.

  2. Measure the ground return at the Stick Shaker 1 A203P1 Pin B.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.

  3. Remove the Stall Protection Computer; inspect the tray, connector and the pins at the connector tray.
  4. Measure the 28 VDC at the SPC from the SPDA 1.
  5. Reinstall the SPC.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.
      NOTE: The SPC is difficult to install due to it’s location.

  6. Replace Stick Shaker 1.
    NOTE: If possible, swap the stick shaker 1 and 2 and confirm that the fault follows the shaker 1 in shaker 2 positions.
  7. Do close out.

Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.