background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults By CAIMS By Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE (CAUTION)
AMBER MESSAGE (ADVISORY)
CYAN MESSAGE (STATUS)
WHITE MESSAGE Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

11/14/25

Message Overview:

Message Name:

PASS DOOR AFT G-LOCK HOOK SNSR/WRG

Message Code:

3231117EL

Associated CAS:

PASSENGER DOOR
(Caution)

Reporting LRU: Landing Gear Electronic Control Unit (LG ECU)
System Description: 52-70-00 - Door Warning
Schematic Diagram: [ Global Express ]  [ G5000 ]  [ Global XRS ] 52-70-00 - Door Warning
Wiring Diagram: [ Global Express ]  [ G5000 ]  [ Global XRS ] 52-70-01 - Door Warning System

Message Description:

Pass Door Aft G-Lock Hook Proximity Sensor has been detected failed by the Landing Gear Electronic Control Unit (LG ECU).

Possible Causes:

  • Pass Door Aft G-Lock Hook Proximity Sensor
  • Landing Gear Electronic Control Unit (LG ECU) (A52)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin: None

Full Throttle Blog/Forum Articles/Infoservice/Newsletter: None

Flight Operation Notifications Manual (FONM): None

NOTES:

  • The logic of the Main Entry Door (Passenger door) FWD G-LOCK HOOK & AFT G-LOCK HOOK sensors on the Channel B of the LGECU is as follow:

    • When door is open:

      • Both sensors are showing LOCKED and Handle sensor is showing NOT STOWED

    • When door is closed:

      • Both sensors are showing NOT LOCKED and Handle sensor is showing STOWED

  • Look at Splice SP698

Quick Links:

Removal of the Landing-Gear Electronic Control-Unit (LG ECU) AMM 32-31-09-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Landing-Gear Electronic Control-Unit (LG ECU) AMM 32-31-09-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Operational Test of the Passenger Door AMM 52-11-00-710-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Passenger Door Proximity-Sensors AMM 52-70-01-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Passenger Door Proximity-Sensors AMM 52-70-01-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wire Repair - Maintenance Practices - ALL SPM 20-12-10-02 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Troubleshooting Recommendations:

  1. Perform wiring checks of the Pass Door Aft Claw Proximity Sensor wires between the LGECU connector A52AP1 and splice SP698.

    From  To Expected Result Result
    A52AP1 - C15 SP698 - A1 Continuity
    A52AP1 - D15 SP698 - B1 Continuity

    1. If wiring checks are not good, repair defective wiring as required and do close out.
    2. If wiring checks are good, continue with next step.

  2. Perform a inspection and wiring checks of splice SP698 contacts/pins.

    1. If wiring checks are not good, repair defective wiring as required and do close out.
    2. If wiring checks are good, continue with next step.

  3. Perform a visual inspection of the wires/harness between Pass Door Aft G-Lock Hook Proximity Sensor and splice SP698. Repair as required.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.

  4. Re-seat LGECU.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.

  5. Replace Pass Door Aft G-Lock Hook Proximity Sensor.

    1. If system checks are good, do close out.
    2. If fault remains, continue with next step.

  6. Replace LGECU.
  7. Do close out.

Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.