background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults By CAIMS By Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE (CAUTION)
AMBER MESSAGE (ADVISORY)
CYAN MESSAGE (STATUS)
WHITE MESSAGE Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

06/03/19

Message Overview:

Fault Message:

[CPC1] SAFETY VALVE #1 /WRG

Fault Code:

2137428ABG

Associated CAS:

SAFETY VALVE OPEN
(Advisory)

Reporting LRU: Cabin Pressure Controller (CPC) 1
System Description: 21-31-00
Schematic Diagram: 21-31-00 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wiring Diagram: 21-31-03 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Fault Description:

The Safety Valve 1 is detected not fully closed.

Possible Causes:

  • Safety Valve 1 (L10)
  • Safety Valve Static Port
  • Data Acquisition Unit (DAU) 1 (A17)
  • Cabin Pressure Controller (CPC) 1 (A21)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin: None

Forum Articles/Infoservice/Newsletter: None

Quick Links:

Removal of the Cabin Pressure Controllers AMM 21-31-01-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Cabin Pressure Controllers AMM 21-31-01-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Safety Valves AMM 21-31-09-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Safety Valves AMM 21-31-09-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Functional Test of the Safety Valves AMM 21-31-09-720-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Data Acquisition Units (DAU) AMM 31-42-01-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Data Acquisition Units (DAU) AMM 31-42-01-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wire Repair - Maintenance Practices - ALL SPM 20-12-10 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Troubleshooting Recommendations:

NOTE: If the Cabin Maximum Differential pressure has been exceeded, disregard the troubleshooting below and investigate the pressurization system.

  1. Perform water leak check of the water system and perform an inspection of the bilge valve.
    NOTE: Water spilled from the aft water system may disturb the static port airflow and consequently partially open the safety valves.
  2. Perform wiring checks of the wire between the Safety Valve 1 and DAU 1.

    1. If the wiring checks are good, repair the defective associated wiring and do close out.
    2. If the wiring checks are good, continue with next step.

  3. Swap DAU 1 with DAU 2.

    1. If the system checks are good, replace the DAU 1 and do close out.
    2. If the fault remains, continue with next step.

  4. Replace CPC 1.
  5. Perform functional test of the safety valves.
  6. Do close out.

Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.