background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults By CAIMS By Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE
(CAUTION)
AMBER MESSAGE
(ADVISORY)
CYAN MESSAGE
(STATUS)
WHITE MESSAGE
Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

07/12/19

Message Overview:

Fault Message:

RH FWD AC BOOST PUMP PRESS SW/WRG

Fault Code:

2844610PK

Associated CAS:

R PRI FUEL PUMPS
(Caution)

R PRI FUEL PUMP
(Advisory)

Reporting LRU: Fuel Management and Quantity Gauging Computer (FMQGC)
System Description: 28-21-00
Schematic Diagram: 28-21-00 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wiring Diagram: 28-21-02 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Fault Description:

R FWD AC BOOST PUMP LMS/WRG FAULT shows when the Right Forward Boost-Pump Pressure is high and low at the same time.

Possible Causes:

  • Right FWD Boost-Pump Pressure-Switch (S15)
  • Fuel Management and Quantity Gauging Computer (FMQGC) (A47)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin: None

Forum Articles/Infoservice/Newsletter: None

Quick Links:

Connect Electrical Power to the Aircraft AMM 24-00-00-861-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Remove the Electrical Power from the Aircraft AMM 24-00-00-861-802 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Opening of Non-Thermal Circuit Breakers AMM 24-00-00-863-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Closing of Non-Thermal Circuit Breakers AMM 24-00-00-863-802 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Electrical/Electronic Safety Precautions AMM 24-00-00-910-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Fuel-System Safety Precautions AMM 28-00-00-910-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the AC Boost-Pump Pressure-Switches AMM 28-21-09-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the AC Boost-Pump Pressure-Switches AMM 28-21-09-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Computer AMM 28-41-01-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Computer AMM 28-41-01-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Access to System Diagnostics AMM 45-45-00-970-804 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Leading Edge Panels (BL52.45 to L/E STA 134.818) AMM 57-41-05-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Leading Edge Panels (BL52.45 to L/E STA134.818) AMM 57-41-05-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Safety Precautions - Maintenance Practices - ALL SPM 20-00-01-02 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wire Repair - Maintenance Practices - ALL SPM 20-12-10-02 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Troubleshooting Recommendations:

  1. Disconnect connector S15P1 (RIGHT FWD BP PRESS SW). Perform a continuity check on the pressure switch side as follows:

    From To Result
    S15P1-G Ground
    S15P1-A Ground

    1. If there is continuity, replace the Right forward boost-pump pressure-switch and do close out.
    2. If there is no continuity, continue with next step.

  2. Remove the FMQGC. Perform a continuity check as follows:

    From To Result
    A47DP1-A12 Ground
    A47DP1-B12 Ground

    1. If there is continuity, repair or replace the defective wiring as wiring and do close out.
    2. If there is no continuity, continue with next step.

  3. Re-rack the FMQGC making sure it is fully and properly inserted into place. Is the fault still present?

    1. If NO, do close out.
    2. If YES, continue with next step.

  4. Replace the FMQGC.
  5. Do close out.
Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.