background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults By CAIMS By Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE (CAUTION)
AMBER MESSAGE (ADVISORY)
CYAN MESSAGE (STATUS)
WHITE MESSAGE Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

02/06/20

Message Overview:

Fault Message:

L DATA ENTRY PLUG CH A WRG MA

Fault Code:

7327122LBR

Associated CAS:

None

Reporting LRU: Left Engine Electronic Controller (EEC)
System Description: 73-20-00
Schematic Diagram: None
Wiring Diagram: 71-50-01 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Fault Description:

The Left Data Entry Plug (DEP) Input to Engine Electronic Controller (EEC) CH A has been detected failed.

Possible Causes:

  • Left Data Entry Plug (DEP)
  • Left Engine Electronic Control Unit (EEC)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin: None

Forum Articles/Infoservice/Newsletter: None

CAUTION: THE DATA ENTRY PLUG MUST BE TRIMMED ACCORDING TO THE INFORMATION GIVEN ON THE DATA ENTRY PLUG COVER. CHANGES TO THE TRIM OF THE DATA ENTRY PLUG WILL CAUSE THE ENGINE TO GIVE INCORRECT THRUST VALUES. THIS MAY CAUSE DAMAGE TO THE ENGINE. IF YOU ARE NOT SURE, CONTACT ROLLS-ROYCE DEUTSCHLAND.

Quick Links:

Access to System Diagnostics AMM 45-45-00-970-804 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Eng Electronic Controller (EEC)
Mod 73-101559		 EMM 73-21-01-000-801-B00 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Eng Electronic Controller (EEC)
Mod 73-101559		 EMM 73-21-01-400-801-B001 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Data Entry Plug EMM 73-21-02-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Data Entry Plug EMM 73-21-02-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wire Repair - Maintenance Practices - ALL SPM 20-12-10-02 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Troubleshooting Recommendations:

  1. Use the PMAT to access CAIMS, SYSTEM DIAGNOSTICS and navigate to the pages for the DEP WIRING for the affected engine. Make sure that on the applicable pages, the DEP trim values are the same as on the DEP cover.
  2. Disconnect the DEP, remove the end cap of the DEP and do the checks that follow:

    • Examine the configurations of the jumper leads in channels A and B and make sure they are the same.
    • Make sure the jumper leads are correctly attached.
    • Examine the EEC pins, DEP sockets and jumper leads to make sure there is no damage or corrosion.

    1. If defects are found, repair/rectify as required.
    2. If no defects are found, continue with next step.

  3. Swap EEC 1 with EEC 2. Is the fault still present?

    1. If YES, continue with next step.
    2. If NO, replace defective EEC.

  4. Perform the Trim of the Data Entry Plug.
    NOTE: Make sure that the DEP trim procedure is checked by a qualified person.
  5. Do close out.

Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.