background
x
loader
Troubleshooting
arrow By ATA By Message Color By Observed Faults By CAIMS By Tips

Select color for CAS message that you wish to troubleshoot

(WARNING)
RED MESSAGE (CAUTION)
AMBER MESSAGE (ADVISORY)
CYAN MESSAGE (STATUS)
WHITE MESSAGE Require immediate crew attention. These messages are accompanied by flashing master warning, triple chime attenson with or without voice message or dedicated tone. Require immediate crew awareness and future crew action may be required in the form of alternate system selection or performance limitation. These message are accompanied by flashing master caution and a single chime. Indicate safe or normal system operation which require crew awareness, over and above the dark cockpit philosophy. Indicate minor failures or reduction in systems capability, which require no crew action.

This page includes :

For AOG assistance contact:

CRC Montreal (YUL)
Quick Links

06/26/19

Message Overview:

Fault Message:

SLAT MOTOR BRAKE/ SFCU/ WRG

Fault Code:

2750024STD

Associated CAS:

SLAT FAIL
(Caution)

SLAT FAULT
(Caution)

SLAT FLAP FAIL
(Caution)

SLAT FLAP FAULT
(Caution)

SLAT HALFSPD
(Advisory)

Reporting LRU: Slat/Flap Control Unit (SFCU)
System Description: 27-53-00
Schematic Diagram: 27-50-00 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wiring Diagram: 27-50-07 [ Global Express ]  [ G5000 ]  [ Global XRS ]
27-50-08 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Fault Description:

The Slat/Flap Control Unit (SFCU) has detected a failure condition in the Slat Motor Brake Circuit for one of the following reasons:

  • There is an open circuit condition in the Power Drive Unit (PDU) Motor/Brake Drive
  • The outputs to the slat motor brake do not agree with inputs from the Slats Brake Drive

Possible Causes:

  • Slat Power Drive Unit (PDU) Motor 1 (B13)
  • Slat Power Drive Unit (PDU) Motor 2 (B14)
  • Slat/Flap Control Unit (SFCU) 1 (A124)
  • Slat/Flap Control Unit (SFCU) 2 (A95)
  • Associated Wiring

Troubleshooting Tips:

Advisory Wire/Service Bulletin: None

Forum Articles/Infoservice/Newsletter: None

There are alternative ways to clear the fault:

  1. On the EMS CDU, select CTRL function and SLAT/FLAP RESET.
    NOTE: Wait at least one minute after SFCU reset to allow self-test to run.
  2. Moving the SFCL to another detent.

Quick Links:

Removal of the Slat/Flap Control Unit (SFCU) AMM 27-51-05-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Slat/Flap Control Unit (SFCU) AMM 27-51-05-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Removal of the Slat Power-Drive Unit (PDU) Motors AMM 27-53-37-000-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Installation of the Slat Power-Drive Unit (PDU) Motors AMM 27-53-37-400-801 [ Global Express ]  [ G5000 ]  [ Global XRS ]
Wire Repair - Maintenance Practices - ALL SPM 20-12-10-02 [ Global Express ]  [ G5000 ]  [ Global XRS ]

Troubleshooting Recommendations:

Fault reported by SFCU 1:

  1. Swap SFCU 1 with SFCU 2.

    1. If system checks are good, replace SFCU 1 and do close out.
    2. If fault remains, continue with next step.

  2. Measure the impedance at SFCU 1 (A124CP1) as follow:

    From To Expected Result Result
    A124CP1-60 A124CP1-61 53.1 to 64.9 Ohms

    1. If resistance is within range, go to step 4.
    2. If fault remains, continue with next step.

  3. Perform wiring checks between SFCU 1 and Slat PDU motor connector.

    1. If wiring checks are not good, repair defective wiring as required and do close out.
    2. If wiring checks are good, continue with next step.

  4. Replace Slat PDU motors.
  5. Do close out.

Fault reported by SFCU 2:

  1. Swap SFCU 2 with SFCU 1.

    1. If system checks are good, replace SFCU 2 and do close out.
    2. If fault remains, continue with next step.

  2. Measure the impedance at SFCU 2 (A95CP1) as follow:

    From To Expected Result Result
    A95CP1-60 A95CP1-61 53.1 to 64.9 Ohms

    1. If resistance is within range, go to step 4.
    2. If fault remains, continue with next step.

  3. Perform wiring checks between SFCU 2 and Slat PDU motor connector.

    1. If wiring checks are not good, repair defective wiring as required and do close out.
    2. If wiring checks are good, continue with next step.

  4. Replace Slat PDU motors.
  5. Do close out.

Registered and/or unregistered trademarks of Bombardier Inc. or its subsidiaries. © 2015 Bombardier Inc. All rights reserved.